The short version
Spray, wait, peel, wipe
- 1. Spray the edgeHold the can 2 to 4 inches away.
- 2. Wait 5 to 10 secondsLet it soak into the adhesive.
- 3. Peel low and slowPress your skin down as you go.
- 4. Wipe dryReady for your next dressing or device.
Before you start
- On skin only, outside the body. Use it on the skin around a stoma or adhesive site.
- Never on open wounds or broken skin. Spray the adhesive around them, not the wound.
- Keep it away from your eyes, nose and mouth. Never spray toward the face.
- It is flammable. No flames, sparks, cigarettes or heaters nearby while you use it and until it dries.
- Use it with fresh air. Don’t breathe in the mist. A bathroom with the fan on or a window open is ideal.
- Adults do the spraying. Keep the can out of reach of children.
Step by step
5 steps to a gentle release
Each step matches the instructions printed on your box, with a tip from us to make it easier.
-
Step 1: Identify the edge
On your boxLocate the edge of the bandage, medical tape, CGM sensor, or ostomy barrier you wish to remove. Ensure the surrounding area is accessible.
TIPLift just a corner with a fingernail so the spray can reach underneath. You don’t need to lift more than that.
-
Step 2: Targeted spray
On your boxHold the bottle 2–4 inches away and spray directly onto the edge of the adhesive. For a wider area, use a misting motion.
TIPSpray under the edge, not on top. Plastic or waterproof backings, like CGM overpatches and clear film dressings, stop the spray from reaching the glue. Short bursts at the edge work best and make your can last longer.
-
Step 3: Wait 5–10 seconds
On your boxAllow the silicone-based formula to penetrate the adhesive bond. No scrubbing is required; the spray will naturally dissolve the “grip” of the glue.
Give it 10 seconds. Thick, old or stubborn adhesive can use the full time, or a little longer.
-
Step 4: Gentle release
On your boxSlowly peel the adhesive away from the skin. If you encounter a stubborn spot, apply one additional small spray to that specific area and wait a few more seconds.
TIPLow and slow: fold the adhesive back over itself, close to the skin, and press your skin down just in front of the edge with your other hand. If it pulls, stop and spray again.
-
Step 5: Clean and ready
On your boxWipe the site with a clean, dry cloth to remove any lifted adhesive. Your skin is now clean and perfectly prepped for your next bandage, medical tape, CGM sensor, or ostomy appliance to adhere firmly and securely.
TIPLet the skin air-dry for a few seconds before the next adhesive goes on. Putting on a new CGM, pod or infusion set? Prep the new site the way your device maker says, usually soap and water, then an alcohol wipe, then let it air-dry.
Tips for what you’re removing
Get the best result for your adhesive
Bandages and medical tape
- Spray where the tape meets the skin. On long strips, peel a little, spray the next section, and keep going.
- Peel low and slow, folding the tape back over itself close to the skin. Going the same way the hair grows is more comfortable.
- Press the skin down right next to the edge with your other hand. This matters most on thin or older skin that tears easily.
- Gauze held on with tape? Spray the tape, not the gauze.
Ostomy barriers and wafers
- At your pouch change, lift a corner of the barrier and spray under the edge. A tiny puff at the top edge runs down under the barrier as you peel.
- Peel slowly while you press the skin away from the barrier. Spray again under the lifting edge as you work your way around.
- Aim at the adhesive, not the stoma. The spray is for the skin around it.
- Leftover barrier ring or paste on the skin? Spray it, wait a few seconds, then wipe gently with a dry cloth. Thicker residue may need a second spray.
- Wipe the skin with a dry paper towel or cloth. If your nurse has you wash after any remover, use mild, non-oily soap and water, rinse and pat dry. Either way, the skin must be completely dry before the new barrier goes on.
- Drying your skin with a hair dryer? Wait until the spray has fully evaporated first. It is flammable, and a hair dryer is a heat source.
Sore, weepy or broken skin around your stoma? Don’t spray it. Check in with your ostomy nurse (WOC nurse).
CGM sensors, pumps and pods
- Spray the outer edge of the adhesive patch, not the sensor, pod or pump itself.
- Only spray the device you are taking off. Keep the mist away from any sensor, pod or reusable transmitter you are still wearing: sprays can loosen its adhesive and some device makers warn they can damage the plastic.
- Using an overpatch? Spray under its edge first and lift it, then do the same for the patch underneath. Used a skin adhesive like Skin-Tac or an extra-sticky overpatch? Plan on a second spray and a little more wait time.
- Wait 10 seconds, then peel the patch back slowly while you press the skin down. Halfway across, spray under the lifted edge again. A cotton swab slid under the edge helps the spray spread.
- Before your next sensor or pod, prep the new site the way your device maker tells you (usually soap and water, then an alcohol wipe, then let it air-dry). Use a different spot each time.
Changing a child’s sensor? A grown-up does the spraying. Let them count down the 10-second timer with you.
Wound and post-surgery dressings
- Spray only the adhesive border. Never spray the pad, the wound or broken skin.
- Work around the border one side at a time, peeling each side back low and slow toward the wound.
- Follow your care team’s plan for when and how to change the dressing. The spray just makes the adhesive part gentler.
- Thin skin-closure strips laid across a cut are usually left to fall off on their own. Only remove them when your care team says so.
If the pad itself is stuck to the wound, that isn’t adhesive and the spray won’t help. Don’t pull it. Ask your nurse or doctor.
Other skin adhesives
- It is made for medical adhesives on skin, like monitor and EKG electrode pads, kinesiology and sports tape, and the dressings around feeding tubes, ports and lines.
- For big pieces of tape, spray and peel in sections.
- Tape on the cheek or near the face? Don’t spray toward the face. Spray a gauze pad instead, then dab the edge of the tape, keeping well away from the eyes.
Not sure it suits your adhesive? Email us and we’ll help.
Pro tips
Small habits, better results
- Spray under the edge, not on topThe glue sits under the patch. Lift a corner and aim the mist underneath; spraying the top of a plastic or waterproof patch does very little.
- Spray, peel, sprayOn long tape or big patches, work in sections. Spray, peel a little, then spray the next part.
- Leftover sticky spots?Spray a gauze pad or soft cloth and wipe gently. No scrubbing needed.
- Feels cool on your skin?That’s normal. It dries in seconds, and fast drying feels cool.
- Let the spray do the workIf the adhesive pulls or turns gummy, it needs more time, not more force. Spray again under the edge and wait a few more seconds.
- Tiny puffs go a long wayA quick puff at the edge, then another as you peel, uses far less than soaking the whole patch. Your can lasts much longer.
Troubleshooting
If something isn’t working
It still pulls or hurts when I peel
Stop peeling. Spray one more small burst on that spot, wait a few more seconds, then peel lower and slower while you press the skin down next to the edge.
The adhesive turned gummy or stickier
It hasn’t fully let go yet. Stop peeling, spray a little more under the edge, wait the full 10 seconds, then peel slowly. Wipe any gummy bits away with a dry gauze pad or cloth. If some is left, wash with mild soap and water and pat dry.
The spray doesn’t get through my CGM overpatch or film dressing
That’s expected: plastic and waterproof backings block the spray from the top. Lift a corner, spray underneath, and keep spraying under the edge as you peel. For a sensor with an overpatch, take the overpatch off first, then the sensor patch.
There is sticky adhesive left on my skin
Spray a gauze pad or a soft, clean cloth and wipe gently. Finish with a clean, dry cloth.
My new sensor, barrier or bandage won’t stick
Make sure the skin is completely dry first. It only takes a few seconds, but a damp or slick surface won’t hold. If your skin still feels slick, wash with mild soap and water, rinse well and pat dry. Skip lotions and creams on that spot.
Nothing comes out, or the spray is weak
- Turn the can so the nozzle opening points at the adhesive, not at you, then press straight down on the white spray head.
- Wipe the nozzle opening with a dry tissue. Never poke it with a pin or try to open the can.
- If the can has been somewhere cold, let it sit at room temperature for a while.
Still nothing? Email us and we will send a replacement.
My skin is red, itchy or sore afterward
A little pinkness right after removing any adhesive is common and should fade within about 30 minutes. If redness lasts longer, or you get itching, soreness or a rash, stop using it: if irritation, redness, or a rash develops, discontinue use and seek medical attention if discomfort persists.
The skin tore or bled while I was peeling
Stop, and don’t spray the torn spot: it’s now broken skin. Rinse it gently with clean water, pat dry and cover it with a clean, non-stick dressing. Call your nurse or doctor if it’s large, deep or keeps bleeding. Next time, wait the full 10 seconds, re-spray as you go and press the skin down right next to the edge.
I got some in my eye
Rinse immediately with running water for at least 20 minutes. If it still hurts or your vision isn’t right, get medical help.
Questions
Your questions, answered
Using it
How long do I wait after spraying?
5 to 10 seconds. If a spot is stubborn, give it one more small spray and wait a few more seconds. Old, thick or extra-strong adhesive may need a little longer.
Do I need to wash it off afterward?
No rinsing is needed. It dries in seconds and is made to leave no oily residue. Just wipe the site with a clean, dry cloth. If your nurse or your device maker tells you to wash the skin before the next one goes on, follow them.
Will my next bandage, sensor or barrier still stick?
Yes. Once the skin is dry it is ready for the next adhesive. If it ever feels slick, wash with mild soap and water and pat dry before you apply.
How much should I use?
A short burst on the edge is usually enough. Use a sweeping, misting motion for a wider area, and add small sprays as you peel rather than soaking everything at once.
Can I spray at an angle or upside down?
For the most even mist, keep the can upright and turn the nozzle toward the edge you’re working on. If the spray sputters, turn the can upright again.
How many uses will I get from one can?
It depends on what you remove and how you spray. A small bandage takes a puff or two; a large dressing or ostomy barrier takes more. Tiny puffs under the edge, added as you peel, make a can last far longer than soaking the whole patch.
Can I use it every day?
Yes. It is made for daily use, including on skin that gets a new dressing, sensor or barrier often. Stop if your skin gets irritated.
Should I use it before putting a new adhesive on?
No. It is a remover, so it only helps take adhesives off. Put new adhesives on clean, dry skin.
What does it work on?
Medical adhesives on skin: bandages, medical tape, wound dressings, ostomy barriers and wafers, CGM sensors, insulin pump and pod patches, and electrode pads. See the tips for your adhesive. It isn’t made for wig, lace or prosthetic glues.
Spray or wipes: which should I use?
The spray reaches under the edges without any rubbing, so it’s great for ostomy barriers, CGM patches and large dressings, and you’re never limited by the size of a wipe. For small leftover spots, spray a gauze pad and wipe.
Will it mark my clothes or furniture?
It dries fast, but aim the mist at the skin and lay a towel down to catch any extra. Keep it off painted or polished surfaces and wipe up any spills.
Does it smell?
There is no fragrance in the ingredients: just a fast-drying silicone (hexamethyldisiloxane) and surfactants, with 0% alcohol.
Why does it feel cold?
It evaporates very quickly, and fast drying feels cool on the skin. That is normal.
Safety
Will it sting?
It is made to be no-sting and painless. Stinging usually comes from alcohol, and this spray has 0% alcohol. If you ever feel burning or stinging, stop and rinse the area with water.
Is it OK for thin, fragile or older skin?
Yes. It is gentle on sensitive skin. For skin that tears easily, the technique matters as much as the spray: wait the full 10 seconds, peel low and slow, and press the skin down next to the edge as you go.
I have very sensitive skin or allergies. Should I test it first?
That’s a good idea. Spray a little on a small patch of healthy skin, let it dry, and wait a day. If you see redness, itching or a rash, don’t use it.
Can I use it for my child?
An adult can use it for a child’s bandage, CGM or pump change. The adult does the spraying: aim only at the adhesive, keep it away from the face, and store the can out of reach. Turning the 10-second timer into a countdown game helps nervous kids. For newborns, premature babies, or skin that is broken or very irritated, ask your child’s care team first.
Can I use it on my pet?
It is made for people. Please ask your vet before using it on a pet’s bandage.
Can two people share one can?
It’s best to give each person their own can, the same way you wouldn’t share a towel. If two people at home use it, the 2-pack gives each of them their own.
Can I use it on an open wound or broken skin?
No. Do not apply it to open wounds or broken skin. Spray only the adhesive on healthy skin around them.
Is it safe around my CGM or insulin pump?
It is made to remove CGM and pump adhesive. Keep the spray on the adhesive patch and off the device itself, and always follow your device maker’s instructions.
Is it flammable?
Yes, it is a highly flammable liquid and vapor. Use and store it away from heat, sparks, open flames and hot surfaces, and don’t smoke while using it. If you use home oxygen, use the spray away from your oxygen equipment and let it dry before going back.
What’s in it?
Hexamethyldisiloxane (a fast-drying, silicone-based ingredient) and surfactants. It contains 0% alcohol. Have a specific allergy? Email us and we’ll help.
Storage and travel
How should I store it?
Keep the can tightly closed in a cool, well-ventilated place away from direct sunlight. Contents are under pressure, so never store it above 120°F (49°C). A parked car can get that hot in minutes. Don’t puncture or burn it, even when empty. Keep it out of reach of children.
Does it expire?
Yes. The best before date is printed on the bottom flap of the box, next to the lot number.
Can I take it on a plane?
The can holds 60 ml (2 fl oz), which is under the 3.4 oz (100 ml) carry-on limit, so it can go in your quart-size liquids bag. It is a medical aerosol; tell the security officer if they ask. Airline rules can change, so check with the TSA or your airline before you fly.
How do I throw away the can?
When it is completely empty, recycle it with metal cans if your local program takes aerosol cans. Never puncture or burn it, and don’t pour the product down a drain.
Your order
My can doesn’t spray. What now?
Try the fixes under troubleshooting. If it still won’t spray, email us and we will make it right with a replacement or refund.
What’s the difference between the 1-pack and the 2-pack?
Same spray, same 60 ml can. The 2-pack gives you two cans, so you always have a spare at home or in your bag.
Where do I reorder?
On Amazon. See the reorder options below.
Watch
See it in action
Questions or a problem?
Product feedback or issues? Email us at support@livaclean.com and we will make it right. If a can won’t spray or you’re not happy with it, we’ll send a replacement or a refund.
Email support@livaclean.comAdd your Amazon order number, and a photo if something is wrong with the can, so we can sort it out fast.
Running low?
Stay stocked up
Change on a schedule? Put it on autopilot
Ostomy and CGM changes happen like clockwork. Choose Subscribe & Save on Amazon and a new can arrives on the schedule you pick. Skip or cancel any time.
Subscribe on Amazon